Wednesday, October 29, 2014
More dovetails
No blog entry for Tuesday as it was pretty much a continuation of the day before. Dovetails. Dovetails. And more dovetails. Other than dovetails, we did spend the last two days on the table saw going over the setup and use. I am pretty comfortable ripping, crosscutting (with the use of a sled) and even dado cutting. Today I used the table saw to cut stock for the next project which is the Shoulder Toolbox. Nothing fancy just a rectangular box to carry tools in to a job site. The pine stock we are using is not the best so I carefully laid out the pieces on a 12 foot board to avoid knots or cupping and to make use of the best grain available. The pieces comprise the two sides, two ends and the bottom. The plan is to dovetail the sides and ends, and then cut a dado for the bottom. An additional dado at the top will hold a small sliding till. Like I said nothing too fancy. I was kinda disappointed that this is our project to finish out basic woodworking (as compared to a more traditional shipwrights chest) but realize that a) we do not have the time available and b) I currently lack the skills to do anything more ambitious. On a side note...I think sometime later in the year and closer to graduation (assuming I make it that far and I have developed the skills), I would like to take on building a proper shipwrights chest. For the time being (and assuming I can make dovetails that look good), I have some ideas for finishing out the toolbox: a holder for chisels and other tools, a saw till for my Japanese saws and finishing it with some green milk paint!
Monday, October 27, 2014
Dovetails
Not sure where to start with so much going on...let's start with Friday. In the morning we had a lecture and slideshow on Intro to Traditional Wood Boat Building Techniques with Jesse. Jesse is a pretty interesting guy as he has traveled to both Ireland and the Basque Country to study traditional boat building techniques. One boat that he studied was the San Juan which was built in 1563 in the Basque Country and sailed as far as Newfoundland. The San Juan was found in 1978 by a Canadian archaeological team and was so well preserved it is the best known example of a 16th century ship. What is quite remarkable is that the timbers used to build the San Juan were cut down almost 70 years earlier than when the boat was built! The boat builders of the Basque Country have a long tradition of relying on specialized farmers to grow trees into the various shapes and sizes needed in wooden boat construction: knees, planks, etc. The wood from these trees were usually (as seen in the San Juan) harvested for the next generations to use.
In the shop on Friday, I completed my spar section and it turned out pretty nice. I have to admit it was a fun project as I was able to move a lot of wood shavings using both my drawknife and bench plane. It was interesting that most students didn't have a drawknife as it was an optional tool on our list. I would definitely recommend getting one. Yes, sharpening it is a pain but well worth it. On the same subject of tools...my Veritas No. 4 bench plane was well worth the money. I have been avoiding using it as I did not want to mess it up somehow sharpening it. The reality was that it was sharp and worked right out of the box. Not sure if any other student can say that.
Monday morning we had a quick visit from Sean at Northwest Sails. Sean runs a sailmaking, rigging and canvas shop above one of the school's buildings. I believe in years past they offered a three-month course as well. This year, Sean is going to offer three week classes in Marlinspike Seamanship. You might ask, what is Marlinspike Seamanship? Well, it is the art that includes the tying of various knots, splicing, working with cable or wire rope with cable or wire rope, even making decorative ornaments from rope or line. Basically anything a sailor can make by himself to make his life on board more comfortable. Some of the items they will be making out of canvas are: a ditty bag, tool rolls, aprons, water bucket, etc.
I've probably failed to mention in an earlier post that the school has arranged for Wayne from Force 10 Sailmaking to run an eight-week course in sailmaking and rigging in the evenings. Wayne is also the Director of the Community Boat Project and quite a character. There are additional costs for these classes and I have chosen not to partake not for that reason but because I would like to focus my efforts on power boats only please!
In the afternoon we watched a video on dovetails called "Dovetail A Drawer" featuring Frank Klausz. Two things...Frank is some crazy German woodworker and he can cut a dovetail joint wicked fast. I'm not sure why the school chose to show this video as I am struggling with my dovetails. My first couple of attempts all failed because of my inability to follow instructions, concentrate and/or just stupid mistakes. If there is one thing I learned today it is...ALWAYS MARK YOUR WASTE. What that means is...cut the piece of wood that you are suppose to be cutting. Anyway, my third and fourth attempts I was able to mark, cut and chisel in the appropriate places; however, the end product was not too pretty. Tomorrow I am hoping to be able to focus and have at least one example of a proper dovetail joint.
For your entertainment pleasure there are two links to videos of Frank Klausz making dovetails:
https://www.youtube.com/watch?v=lrAAglKLPh8
https://www.youtube.com/watch?v=G-o4jryTkUc
Please watch this one. Frank is racing another a guy in making a dovetail (notice how after he finishes he kinda hovers over the other guy):
https://www.youtube.com/watch?v=aN9l4hQ19HE
In the shop on Friday, I completed my spar section and it turned out pretty nice. I have to admit it was a fun project as I was able to move a lot of wood shavings using both my drawknife and bench plane. It was interesting that most students didn't have a drawknife as it was an optional tool on our list. I would definitely recommend getting one. Yes, sharpening it is a pain but well worth it. On the same subject of tools...my Veritas No. 4 bench plane was well worth the money. I have been avoiding using it as I did not want to mess it up somehow sharpening it. The reality was that it was sharp and worked right out of the box. Not sure if any other student can say that.
Monday morning we had a quick visit from Sean at Northwest Sails. Sean runs a sailmaking, rigging and canvas shop above one of the school's buildings. I believe in years past they offered a three-month course as well. This year, Sean is going to offer three week classes in Marlinspike Seamanship. You might ask, what is Marlinspike Seamanship? Well, it is the art that includes the tying of various knots, splicing, working with cable or wire rope with cable or wire rope, even making decorative ornaments from rope or line. Basically anything a sailor can make by himself to make his life on board more comfortable. Some of the items they will be making out of canvas are: a ditty bag, tool rolls, aprons, water bucket, etc.
I've probably failed to mention in an earlier post that the school has arranged for Wayne from Force 10 Sailmaking to run an eight-week course in sailmaking and rigging in the evenings. Wayne is also the Director of the Community Boat Project and quite a character. There are additional costs for these classes and I have chosen not to partake not for that reason but because I would like to focus my efforts on power boats only please!
In the afternoon we watched a video on dovetails called "Dovetail A Drawer" featuring Frank Klausz. Two things...Frank is some crazy German woodworker and he can cut a dovetail joint wicked fast. I'm not sure why the school chose to show this video as I am struggling with my dovetails. My first couple of attempts all failed because of my inability to follow instructions, concentrate and/or just stupid mistakes. If there is one thing I learned today it is...ALWAYS MARK YOUR WASTE. What that means is...cut the piece of wood that you are suppose to be cutting. Anyway, my third and fourth attempts I was able to mark, cut and chisel in the appropriate places; however, the end product was not too pretty. Tomorrow I am hoping to be able to focus and have at least one example of a proper dovetail joint.
For your entertainment pleasure there are two links to videos of Frank Klausz making dovetails:
https://www.youtube.com/watch?v=lrAAglKLPh8
https://www.youtube.com/watch?v=G-o4jryTkUc
Please watch this one. Frank is racing another a guy in making a dovetail (notice how after he finishes he kinda hovers over the other guy):
https://www.youtube.com/watch?v=aN9l4hQ19HE
Thursday, October 23, 2014
It is your Destiny...
![]() |
| Destiny racing in the Banderas Bay Regatta in Mexico |
Work in the shop included finishing both the small and large spar gauge, sharpening a brand new drawknife and then making some wood shavings using the drawknife on a 4 x 4 piece of fir. The goal is to turn the square stock into a round spar. Step one was completed today by shaving the wood down into a octagon. Tomorrow I will finish tuning my No. 4 plane and then use it to further cut the octagon into 16 sides.
Wednesday, October 22, 2014
Japanese woodworking
Lecture today was actually a video from a series called "The Traditional Crafts of Japan: Kyoto Joinery". What is there to say? These guys put us to shame. The level of craftsmanship is just unbelievable. Apparently when apprenticing in joinery in Japan you do not pick up a tool for the first three years...all you do is watch a master at work. Also if you happen to step over a master's saw as an apprentice, you are done for good for disrespecting the tool! The appreciation and respect for their tools and what they are doing was inspiring. Here are some quotes: "If the blade is sharp, even an amateur can use a plane." "If your tools are in good condition, they'll even cover up a lack of skill." "People often judge a craftsman's skill, not by the finished product but by his tools." And my favorite, "The wood is a living thing, so it's cruel to the wood itself, if you make a mistake." I think I need to spend more time on sharpening and conditioning my tools based on these quotes!
If you are interested the video can be found at: https://www.youtube.com/watch?v=-aRZT0PYhJU
In the shop today I completed one side of my rabbet. We then move on to creating spar gauges in two sizes. A spar gauge is basically a tool used to mark a square piece of stock in order to make it round. It is used in the first step of turning the square stock into an eight-sided square stock. The stock is then cut down into 16 sides, 32 sides and so on, until it is round. Tomorrow I will complete the larger of the two spar gauges and then move onto actually making a spar.
If you are interested the video can be found at: https://www.youtube.com/watch?v=-aRZT0PYhJU
In the shop today I completed one side of my rabbet. We then move on to creating spar gauges in two sizes. A spar gauge is basically a tool used to mark a square piece of stock in order to make it round. It is used in the first step of turning the square stock into an eight-sided square stock. The stock is then cut down into 16 sides, 32 sides and so on, until it is round. Tomorrow I will complete the larger of the two spar gauges and then move onto actually making a spar.
Tuesday, October 21, 2014
Rabbet
The mallet is finished! Finally. I will probably work on it a little more when I have some available time to enhance it's appearance. The good news is that it is functional and I used it quite extensively today in working on my rabbet.
Lecture this morning was on the Parts of a Wooden Boat given by Sean, the Lead Instructor for the school. Lot's of information. Some known but mostly things I have never heard of. Do you know what the following parts of a wooden boat are: a) Sampson post, b) Breast hook, c) Garboard and d) Chainplate? (see answers below)
Rabbet. For this project we are cutting a rabbet groove in a piece of fir that represents a fictional stem on a boat. The marking of the profile, rabbet and beading are done using nails and a piece of batten. The back rabbet is then laid out between the rabbet and beading. This represents the angle at which the planks on the boat will attach to the stem. To represent the planks, we used what is called a "fid" which is the same thickness as the planks. Using a chisel, material is removed from the rabbet, then down to the back rabbet and up to the bearding, allowing the "fid" to fit in at the correct angle. This process is time consuming and somewhat laborious. I'm not complaining since I'm standing at a bench with my "stem" clamped down. Usually this work is done on a boat in different areas and positions around the backbone...probably somewhere best reached from your back!
a) A strong vertical post used to support a ship's windlass and the heel of a ship's bowsprit.
b) A roughly triangular piece of wood fitted immediately aft of the stem and between the two inwales or sheer clamps usually in a wooden dinghy.
c) The strake immediately adjacent to the keel in a traditional wooden boat.
d) A strip of strong metal, often stainless steel, through-bolted to the topsides and a frame and protruding above deck level to take the load of a stay in a sailboat.
Lecture this morning was on the Parts of a Wooden Boat given by Sean, the Lead Instructor for the school. Lot's of information. Some known but mostly things I have never heard of. Do you know what the following parts of a wooden boat are: a) Sampson post, b) Breast hook, c) Garboard and d) Chainplate? (see answers below)
Rabbet. For this project we are cutting a rabbet groove in a piece of fir that represents a fictional stem on a boat. The marking of the profile, rabbet and beading are done using nails and a piece of batten. The back rabbet is then laid out between the rabbet and beading. This represents the angle at which the planks on the boat will attach to the stem. To represent the planks, we used what is called a "fid" which is the same thickness as the planks. Using a chisel, material is removed from the rabbet, then down to the back rabbet and up to the bearding, allowing the "fid" to fit in at the correct angle. This process is time consuming and somewhat laborious. I'm not complaining since I'm standing at a bench with my "stem" clamped down. Usually this work is done on a boat in different areas and positions around the backbone...probably somewhere best reached from your back!
a) A strong vertical post used to support a ship's windlass and the heel of a ship's bowsprit.
b) A roughly triangular piece of wood fitted immediately aft of the stem and between the two inwales or sheer clamps usually in a wooden dinghy.
c) The strake immediately adjacent to the keel in a traditional wooden boat.
d) A strip of strong metal, often stainless steel, through-bolted to the topsides and a frame and protruding above deck level to take the load of a stay in a sailboat.
Monday, October 20, 2014
Sailing
No blog on Friday for three reasons: 1) it was a shortened day because of the potluck dinner that evening, 2) I stayed a couple of extra hours to get caught up and actually fell further behind and 3) by the time I got home to Seattle I was too tired. Some quick notes about Friday's classroom session. It was a session on the power jointer and the planer given by Peter (more on Peter later). Peter is a no nonsense straightforward passionate type of guy (he's exactly what you picture a boat builder would be). He started off by reminding us that these tools can and will maim. The jointer is used to flatten the face of a board. The planer is used to set the thickness of a board. Peter is the first instructor to actually turn the machines on in the classroom and demonstrate how they are used! The one thing I will take away is that you put stock "over" the jointer and "through" the planer. During my time in the shop that afternoon I continued to work on the mallet handle and had hoped to get checked off on my mitered bridle joint. Unfortunately that didn't happen and turns out I have to start all over again. So as of today I still need to finish a mitered bridle and the carlins. Which takes me to my weekend project of building a bench in the garage so that I will be able to do some "homework" on the weekends. It exactly didn't get done (mainly because I forgot my cordless drill at school), so I guess it will have to wait until next weekend.
Today was actually a pretty good day. Morning session was on Basic Sailing and Rigs, and again was taught by Peter. He asked the class how many people considered themselves experienced sailors, how many have sailed before and how many have no clue about sailing. I didn't raise my hand. Not sure why, probably because I don't consider myself a sailor from my fooling around with the laser's at The Citadel and our sunfish. Peter went over some basic sailing maneuvering, parts of the sail and types of different sails. He gave a slide show on all kinds of different sailboats and rigs from all over the world. Then he showed us a film...but first I need to tell a little about Peter. I don't really know him at all (but I hope to). He is one of the two instructors for the small craft program, so if I stay in that program there is 50/50 chance I would get him as an instructor. What I do know is that he apprenticed under Donlon Arques in Sausalito, CA (the Arques School is named after him and where I would really love to do an apprenticeship), worked at Mystic seaport, did a bunch of other things and then spent 10 years in Hollywood building boats for all three Pirates of the Caribbean movies, among others! So the film he showed us was made by him when he was in film school and shows him on his sailboat, Bertie, on a voyage from San Francisco to British Columbia in search of Allen & Sherri Farell and their boat, China Cloud. To say that that the Farell's were interesting and unique is a vast understatement and you can really see why Peter has a fond attraction for them. Boat Building and sailing is more than a hobby or occupation to these people...it is a way of life. When watching the film certain words came to mind. Freedom. Independence. Simplicity. Very powerful stuff. I hope that my journey going forward will reveal a little bit of each.
A highly suggest that if you have a few minutes watch the film (it's in three parts) and a video about the Farrel's:
Allen Farrell, CHINA CLOUD, BERTIE and Chinese junk rig at sea
Part 1: https://www.youtube.com/watch?v=Zw6mdrcDL1o
Part 2: https://www.youtube.com/watch?v=tFb3AfxxgO0
Part 3: https://www.youtube.com/watch?v=XIBDOUSd-Ag
Allen Farrell: Boat Builder
https://www.youtube.com/watch?v=0O52F8yYPSw
In the shop today I continued to work on the mallet. One quick note. The right tool does make the job easier. I am so glad that I bought a 1/2" mortise chisel this weekend because I was able to make quick work of the mortise in the mallet head. I then finished up the handle and cut two slots at the top. With the handle inserted into the mallet handle I added a little glue and three hand cut wedges. The mallet handle and head will not separate in my lifetime at least! Some finish up work tomorrow and I'm done. We had a quick demonstration and discussion on rabbet's (no, not the little furry kind that you put into stew) which are grooves where the planks intersect with the centerline timbers (stem, keel, etc.). More on that tomorrow.
Today was actually a pretty good day. Morning session was on Basic Sailing and Rigs, and again was taught by Peter. He asked the class how many people considered themselves experienced sailors, how many have sailed before and how many have no clue about sailing. I didn't raise my hand. Not sure why, probably because I don't consider myself a sailor from my fooling around with the laser's at The Citadel and our sunfish. Peter went over some basic sailing maneuvering, parts of the sail and types of different sails. He gave a slide show on all kinds of different sailboats and rigs from all over the world. Then he showed us a film...but first I need to tell a little about Peter. I don't really know him at all (but I hope to). He is one of the two instructors for the small craft program, so if I stay in that program there is 50/50 chance I would get him as an instructor. What I do know is that he apprenticed under Donlon Arques in Sausalito, CA (the Arques School is named after him and where I would really love to do an apprenticeship), worked at Mystic seaport, did a bunch of other things and then spent 10 years in Hollywood building boats for all three Pirates of the Caribbean movies, among others! So the film he showed us was made by him when he was in film school and shows him on his sailboat, Bertie, on a voyage from San Francisco to British Columbia in search of Allen & Sherri Farell and their boat, China Cloud. To say that that the Farell's were interesting and unique is a vast understatement and you can really see why Peter has a fond attraction for them. Boat Building and sailing is more than a hobby or occupation to these people...it is a way of life. When watching the film certain words came to mind. Freedom. Independence. Simplicity. Very powerful stuff. I hope that my journey going forward will reveal a little bit of each.
A highly suggest that if you have a few minutes watch the film (it's in three parts) and a video about the Farrel's:
Allen Farrell, CHINA CLOUD, BERTIE and Chinese junk rig at sea
Part 1: https://www.youtube.com/watch?v=Zw6mdrcDL1o
Part 2: https://www.youtube.com/watch?v=tFb3AfxxgO0
Part 3: https://www.youtube.com/watch?v=XIBDOUSd-Ag
Allen Farrell: Boat Builder
https://www.youtube.com/watch?v=0O52F8yYPSw
In the shop today I continued to work on the mallet. One quick note. The right tool does make the job easier. I am so glad that I bought a 1/2" mortise chisel this weekend because I was able to make quick work of the mortise in the mallet head. I then finished up the handle and cut two slots at the top. With the handle inserted into the mallet handle I added a little glue and three hand cut wedges. The mallet handle and head will not separate in my lifetime at least! Some finish up work tomorrow and I'm done. We had a quick demonstration and discussion on rabbet's (no, not the little furry kind that you put into stew) which are grooves where the planks intersect with the centerline timbers (stem, keel, etc.). More on that tomorrow.
Thursday, October 16, 2014
Mallet
Today we finished the lecture series on Wood Technology. The main topic of discussion was rot. Rot is caused by fungus which derives it food from a host plant (in this case wood which contains sugars). The three stages of rot are: mold, stain and decay. The first two are on the surface and can be treated with a simple solution of vinegar and water. Decay is a little more complicated to fix and hence why many of us would like to go into the repair and restoration business. Like many other trades, the lack of maintenance by owners leads to steady work in the boatyard for shipwrights! One interesting fact that I did not know is that "waterlogged" wood is rot resistance. I'm sure you are asking how can that be? Well, one of the elements that fungi needs to thrive is oxygen. Go figure.
In the shop I started working on the mallet project. I first drew out the shape of the handle (half sections of both the profile and thickness) on a piece of door skin. Then cut the door skin on the bandsaw to create a template to transfer the shape to my piece of ash stock. I then cut the ash stock on the bandsaw and made a rough looking handle. Tomorrow will be spent shaping the handle with the flat spokeshave. For the mallet head, after finding the center and laying out the mortise, I used a forstner bit on the drill press to drill a hole in the maple stock from the top and bottom. Believe it or not but the holes line up almost exactly in line. I have lot's of chiseling to look forward tomorrow to complete the mortise.
In the shop I started working on the mallet project. I first drew out the shape of the handle (half sections of both the profile and thickness) on a piece of door skin. Then cut the door skin on the bandsaw to create a template to transfer the shape to my piece of ash stock. I then cut the ash stock on the bandsaw and made a rough looking handle. Tomorrow will be spent shaping the handle with the flat spokeshave. For the mallet head, after finding the center and laying out the mortise, I used a forstner bit on the drill press to drill a hole in the maple stock from the top and bottom. Believe it or not but the holes line up almost exactly in line. I have lot's of chiseling to look forward tomorrow to complete the mortise.
Subscribe to:
Posts (Atom)

